Airplane gently rocking its wings during whole flightWhy do wings of passenger jet go dark during a flight?How do wings generate lift?Why did the CL-400 Suntan have engines on the ends of its wings?What would be the lift formula for straight wings?Why do wall-to-wall airfoils in wind tunnels produce no (or infinitesimal) downwash?Are aircraft wings airtight?What creates most drag during flight: fuselage or wings?Strut braced or wire braced airplane wings?Does the Lilium VTOL wings produces lift during takeoff?Wing Shape: Long/Wide Span Wings vs Deep Wings
What reasons are there for a Capitalist to oppose a 100% inheritance tax?
What is the fastest integer factorization to break RSA?
Can I hook these wires up to find the connection to a dead outlet?
Do creatures with a speed 0ft., fly 30ft. (hover) ever touch the ground?
Why were 5.25" floppy drives cheaper than 8"?
files created then deleted at every second in tmp directory
Why are UK visa biometrics appointments suspended at USCIS Application Support Centers?
In Bayesian inference, why are some terms dropped from the posterior predictive?
How exploitable/balanced is this homebrew spell: Spell Permanency?
How can I deal with my CEO asking me to hire someone with a higher salary than me, a co-founder?
Why didn't Boeing produce its own regional jet?
Could the museum Saturn V's be refitted for one more flight?
Did 'Cinema Songs' exist during Hiranyakshipu's time?
Can someone clarify Hamming's notion of important problems in relation to modern academia?
Which ISO should I use for the cleanest image?
In the UK, is it possible to get a referendum by a court decision?
What's the meaning of "Sollensaussagen"?
Is it "common practice in Fourier transform spectroscopy to multiply the measured interferogram by an apodizing function"? If so, why?
Finitely generated matrix groups whose eigenvalues are all algebraic
Is this draw by repetition?
How to coordinate airplane tickets?
What is the opposite of "eschatology"?
Rotate ASCII Art by 45 Degrees
Bullying boss launched a smear campaign and made me unemployable
Airplane gently rocking its wings during whole flight
Why do wings of passenger jet go dark during a flight?How do wings generate lift?Why did the CL-400 Suntan have engines on the ends of its wings?What would be the lift formula for straight wings?Why do wall-to-wall airfoils in wind tunnels produce no (or infinitesimal) downwash?Are aircraft wings airtight?What creates most drag during flight: fuselage or wings?Strut braced or wire braced airplane wings?Does the Lilium VTOL wings produces lift during takeoff?Wing Shape: Long/Wide Span Wings vs Deep Wings
$begingroup$
I was on a flight with a regional airline a while ago in a Bombardier airplane (if I recall correctly) where the airplane would slowly and gently rock its wings just a little bit on the whole flight. I wasn't a long flight but wasn't very short either at roughly 2 hours.
It was very comfortable and the rocking made for a very gentle cradle feeling 🙂
My question is, why would that be? Is it economical to do so for any reason? Is it possible that the airplane had no autopilot and the pilot was flying it by hand? What could cause such a behaviour?
aerodynamics wing economics
asked yesterday
Délisson JunioDélisson Junio
427617
$endgroup$
add a comment |
$begingroup$
I was on a flight with a regional airline a while ago in a Bombardier airplane (if I recall correctly) where the airplane would slowly and gently rock its wings just a little bit on the whole flight. I wasn't a long flight but wasn't very short either at roughly 2 hours.
It was very comfortable and the rocking made for a very gentle cradle feeling 🙂
My question is, why would that be? Is it economical to do so for any reason? Is it possible that the airplane had no autopilot and the pilot was flying it by hand? What could cause such a behaviour?
aerodynamics wing economics
asked yesterday
Délisson JunioDélisson Junio
427617
$endgroup$
3
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
yesterday
1
$begingroup$
Are you talking about this? It is pretty common for airplanes.
$endgroup$
– havenoidea
yesterday
add a comment |
$begingroup$
I was on a flight with a regional airline a while ago in a Bombardier airplane (if I recall correctly) where the airplane would slowly and gently rock its wings just a little bit on the whole flight. I wasn't a long flight but wasn't very short either at roughly 2 hours.
It was very comfortable and the rocking made for a very gentle cradle feeling 🙂
My question is, why would that be? Is it economical to do so for any reason? Is it possible that the airplane had no autopilot and the pilot was flying it by hand? What could cause such a behaviour?
aerodynamics wing economics
asked yesterday
Délisson JunioDélisson Junio
427617
$endgroup$
I was on a flight with a regional airline a while ago in a Bombardier airplane (if I recall correctly) where the airplane would slowly and gently rock its wings just a little bit on the whole flight. I wasn't a long flight but wasn't very short either at roughly 2 hours.
It was very comfortable and the rocking made for a very gentle cradle feeling 🙂
My question is, why would that be? Is it economical to do so for any reason? Is it possible that the airplane had no autopilot and the pilot was flying it by hand? What could cause such a behaviour?
aerodynamics wing economics
aerodynamics wing economics
asked yesterday
Délisson JunioDélisson Junio
427617
asked yesterday
Délisson JunioDélisson Junio
427617
asked yesterday
Délisson JunioDélisson Junio
427617
asked yesterday
Délisson JunioDélisson Junio
427617
asked yesterday
Délisson JunioDélisson Junio
427617
427617
3
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
yesterday
1
$begingroup$
Are you talking about this? It is pretty common for airplanes.
$endgroup$
– havenoidea
yesterday
add a comment |
3
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
yesterday
1
$begingroup$
Are you talking about this? It is pretty common for airplanes.
$endgroup$
– havenoidea
yesterday
3
3
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
yesterday
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
yesterday
1
1
$begingroup$
Are you talking about this? It is pretty common for airplanes.
$endgroup$
– havenoidea
yesterday
$begingroup$
Are you talking about this? It is pretty common for airplanes.
$endgroup$
– havenoidea
yesterday
add a comment |
1 Answer
1
active
oldest
votes
$begingroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
answered yesterday
John KJohn K
23.9k13473
$endgroup$
5
$begingroup$
For those who want to know the little tiny left, little tiny right would be a bad hysteresis. Similar to how you ac/heat does not come on right at the correct temp. It waits for it to be out of a range, higher for heat to turn off, lower for ac to turn off.
$endgroup$
– NDEthos
yesterday
2
$begingroup$
@NDEthos: Are they really using simple thermostat-style controllers instead of properly configured PID controllers?
$endgroup$
– Michael
yesterday
2
$begingroup$
I just used a thermostat as an example. Even with a PID I would assume the concept of hysteresis still applies.
$endgroup$
– NDEthos
yesterday
$begingroup$
But shouldn't an aircraft be roll-stable at cruise naturally?
$endgroup$
– Délisson Junio
yesterday
$begingroup$
It's way more complicated with swept wing airplanes because of the strong roll/yaw couple caused by the sweep. The sweep is a bit like having way too much dihedral; any yawing motions set up sympathetic rolling motions (setting up a kind of S shaped flight path - dutch roll) and they may dampen themselves out, but in some configurations the damping is too weak, or is negative (dutch roll), necessitating a yaw damper system that works the rudder to actively stop or prevent yawing movements. I suspect that the condition you were seeing was a feedback or hysterisis loop within the YD system.
$endgroup$
– John K
yesterday
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("mathjaxEditing", function ()
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
);
);
, "mathjax-editing");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "528"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f61851%2fairplane-gently-rocking-its-wings-during-whole-flight%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
answered yesterday
John KJohn K
23.9k13473
$endgroup$
5
$begingroup$
For those who want to know the little tiny left, little tiny right would be a bad hysteresis. Similar to how you ac/heat does not come on right at the correct temp. It waits for it to be out of a range, higher for heat to turn off, lower for ac to turn off.
$endgroup$
– NDEthos
yesterday
2
$begingroup$
@NDEthos: Are they really using simple thermostat-style controllers instead of properly configured PID controllers?
$endgroup$
– Michael
yesterday
2
$begingroup$
I just used a thermostat as an example. Even with a PID I would assume the concept of hysteresis still applies.
$endgroup$
– NDEthos
yesterday
$begingroup$
But shouldn't an aircraft be roll-stable at cruise naturally?
$endgroup$
– Délisson Junio
yesterday
$begingroup$
It's way more complicated with swept wing airplanes because of the strong roll/yaw couple caused by the sweep. The sweep is a bit like having way too much dihedral; any yawing motions set up sympathetic rolling motions (setting up a kind of S shaped flight path - dutch roll) and they may dampen themselves out, but in some configurations the damping is too weak, or is negative (dutch roll), necessitating a yaw damper system that works the rudder to actively stop or prevent yawing movements. I suspect that the condition you were seeing was a feedback or hysterisis loop within the YD system.
$endgroup$
– John K
yesterday
add a comment |
$begingroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
answered yesterday
John KJohn K
23.9k13473
$endgroup$
5
$begingroup$
For those who want to know the little tiny left, little tiny right would be a bad hysteresis. Similar to how you ac/heat does not come on right at the correct temp. It waits for it to be out of a range, higher for heat to turn off, lower for ac to turn off.
$endgroup$
– NDEthos
yesterday
2
$begingroup$
@NDEthos: Are they really using simple thermostat-style controllers instead of properly configured PID controllers?
$endgroup$
– Michael
yesterday
2
$begingroup$
I just used a thermostat as an example. Even with a PID I would assume the concept of hysteresis still applies.
$endgroup$
– NDEthos
yesterday
$begingroup$
But shouldn't an aircraft be roll-stable at cruise naturally?
$endgroup$
– Délisson Junio
yesterday
$begingroup$
It's way more complicated with swept wing airplanes because of the strong roll/yaw couple caused by the sweep. The sweep is a bit like having way too much dihedral; any yawing motions set up sympathetic rolling motions (setting up a kind of S shaped flight path - dutch roll) and they may dampen themselves out, but in some configurations the damping is too weak, or is negative (dutch roll), necessitating a yaw damper system that works the rudder to actively stop or prevent yawing movements. I suspect that the condition you were seeing was a feedback or hysterisis loop within the YD system.
$endgroup$
– John K
yesterday
add a comment |
$begingroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
answered yesterday
John KJohn K
23.9k13473
$endgroup$
I can give you two theories. One is it's a very very mild case of "overcontrolling" of the autopilot roll servo as it chases a perfectly wings level condition and continuously applies a teeny bit too much left, ooops, then a teeny bit too much right, oops, and back and forth.
The aileron control circuit is cables running to hydraulics at the ailerons, with a spring loaded roller in a curvy V shaped cam device that centers each side of the aileron cable circuit. The breakout force to move the control circuit out of neutral (forcing the roller from the center V of the cam) is fairly high and this can actually be a problem for pilots hand flying at higher speeds where the ailerons are quite snappy - applying enough force to break out the circuit and move the wheel left gives too much, and back the other way... too much... and back and forth you go. It can be a pain.
The autopilot servo is basically a little electric winch connected into the aileron cable circuit, doing the same thing the pilot does. It could be that something in the electronic control loop, or mechanically within the servo, can cause this back and forth oscillation on some airplanes, sometimes. It may be related to wear and backlash within the autopilot servo.
The other theory is it's more or less something similar, but in the yaw mode with the yaw damper not able to fully dampen out a dutch roll mode because the amplitude was within the yaw damper's sensitivity band. Dutch roll is rolling due to yaw, which in swept wing jets is very strong, such that it can set up continuous self energizing oscillation. It could also be related to wear and backlash in the yaw damper actuator, which is a pair of electric linear actuators (little electric screw jacks), in the push rods going to the rudder hydraulics.
If you saw the wing tip just going straight up and down, it's mostly likely the first theory. If you could see the winglet moving in a little circle (indicating rolling and yawing), it's more likely the second theory.
I can really only theorize because the issue was never fully explored on the RJ program as this phenomenon was random, very minor and not dangerous, and was never complained about by operators because only someone sitting near the wings that can look straight out at the winglet ever notices it. It was never bad enough to get anyone sick for example, at least on the RJ fleet.
answered yesterday
John KJohn K
23.9k13473
answered yesterday
John KJohn K
23.9k13473
answered yesterday
John KJohn K
23.9k13473
answered yesterday
John KJohn K
23.9k13473
23.9k13473
5
$begingroup$
For those who want to know the little tiny left, little tiny right would be a bad hysteresis. Similar to how you ac/heat does not come on right at the correct temp. It waits for it to be out of a range, higher for heat to turn off, lower for ac to turn off.
$endgroup$
– NDEthos
yesterday
2
$begingroup$
@NDEthos: Are they really using simple thermostat-style controllers instead of properly configured PID controllers?
$endgroup$
– Michael
yesterday
2
$begingroup$
I just used a thermostat as an example. Even with a PID I would assume the concept of hysteresis still applies.
$endgroup$
– NDEthos
yesterday
$begingroup$
But shouldn't an aircraft be roll-stable at cruise naturally?
$endgroup$
– Délisson Junio
yesterday
$begingroup$
It's way more complicated with swept wing airplanes because of the strong roll/yaw couple caused by the sweep. The sweep is a bit like having way too much dihedral; any yawing motions set up sympathetic rolling motions (setting up a kind of S shaped flight path - dutch roll) and they may dampen themselves out, but in some configurations the damping is too weak, or is negative (dutch roll), necessitating a yaw damper system that works the rudder to actively stop or prevent yawing movements. I suspect that the condition you were seeing was a feedback or hysterisis loop within the YD system.
$endgroup$
– John K
yesterday
add a comment |
5
$begingroup$
For those who want to know the little tiny left, little tiny right would be a bad hysteresis. Similar to how you ac/heat does not come on right at the correct temp. It waits for it to be out of a range, higher for heat to turn off, lower for ac to turn off.
$endgroup$
– NDEthos
yesterday
2
$begingroup$
@NDEthos: Are they really using simple thermostat-style controllers instead of properly configured PID controllers?
$endgroup$
– Michael
yesterday
2
$begingroup$
I just used a thermostat as an example. Even with a PID I would assume the concept of hysteresis still applies.
$endgroup$
– NDEthos
yesterday
$begingroup$
But shouldn't an aircraft be roll-stable at cruise naturally?
$endgroup$
– Délisson Junio
yesterday
$begingroup$
It's way more complicated with swept wing airplanes because of the strong roll/yaw couple caused by the sweep. The sweep is a bit like having way too much dihedral; any yawing motions set up sympathetic rolling motions (setting up a kind of S shaped flight path - dutch roll) and they may dampen themselves out, but in some configurations the damping is too weak, or is negative (dutch roll), necessitating a yaw damper system that works the rudder to actively stop or prevent yawing movements. I suspect that the condition you were seeing was a feedback or hysterisis loop within the YD system.
$endgroup$
– John K
yesterday
5
5
$begingroup$
For those who want to know the little tiny left, little tiny right would be a bad hysteresis. Similar to how you ac/heat does not come on right at the correct temp. It waits for it to be out of a range, higher for heat to turn off, lower for ac to turn off.
$endgroup$
– NDEthos
yesterday
$begingroup$
For those who want to know the little tiny left, little tiny right would be a bad hysteresis. Similar to how you ac/heat does not come on right at the correct temp. It waits for it to be out of a range, higher for heat to turn off, lower for ac to turn off.
$endgroup$
– NDEthos
yesterday
2
2
$begingroup$
@NDEthos: Are they really using simple thermostat-style controllers instead of properly configured PID controllers?
$endgroup$
– Michael
yesterday
$begingroup$
@NDEthos: Are they really using simple thermostat-style controllers instead of properly configured PID controllers?
$endgroup$
– Michael
yesterday
2
2
$begingroup$
I just used a thermostat as an example. Even with a PID I would assume the concept of hysteresis still applies.
$endgroup$
– NDEthos
yesterday
$begingroup$
I just used a thermostat as an example. Even with a PID I would assume the concept of hysteresis still applies.
$endgroup$
– NDEthos
yesterday
$begingroup$
But shouldn't an aircraft be roll-stable at cruise naturally?
$endgroup$
– Délisson Junio
yesterday
$begingroup$
But shouldn't an aircraft be roll-stable at cruise naturally?
$endgroup$
– Délisson Junio
yesterday
$begingroup$
It's way more complicated with swept wing airplanes because of the strong roll/yaw couple caused by the sweep. The sweep is a bit like having way too much dihedral; any yawing motions set up sympathetic rolling motions (setting up a kind of S shaped flight path - dutch roll) and they may dampen themselves out, but in some configurations the damping is too weak, or is negative (dutch roll), necessitating a yaw damper system that works the rudder to actively stop or prevent yawing movements. I suspect that the condition you were seeing was a feedback or hysterisis loop within the YD system.
$endgroup$
– John K
yesterday
$begingroup$
It's way more complicated with swept wing airplanes because of the strong roll/yaw couple caused by the sweep. The sweep is a bit like having way too much dihedral; any yawing motions set up sympathetic rolling motions (setting up a kind of S shaped flight path - dutch roll) and they may dampen themselves out, but in some configurations the damping is too weak, or is negative (dutch roll), necessitating a yaw damper system that works the rudder to actively stop or prevent yawing movements. I suspect that the condition you were seeing was a feedback or hysterisis loop within the YD system.
$endgroup$
– John K
yesterday
add a comment |
Thanks for contributing an answer to Aviation Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f61851%2fairplane-gently-rocking-its-wings-during-whole-flight%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
3
$begingroup$
Sounds like the dutch roll mode was working. Were you high and fast at the time?
$endgroup$
– MikeY
yesterday
1
$begingroup$
Are you talking about this? It is pretty common for airplanes.
$endgroup$
– havenoidea
yesterday